产品咨询订购电话: 134-1834-4523
 当前位置:模具防锈剂首页 - 新闻动态 - 技术分享 - 模具维修

塑料模具专业英语

发布时间:2016.09.24 新闻来源:脱模剂_防锈剂_清洗剂_顶针油_深圳金利源精细科技有限公司

模具述语

一、入水:gate

进入位: gate location

水口形式:gate type

大水口:edge gate

细水口: pin-point gate

水口大小:gate size

转水口: switching runner/gate

唧嘴口径: sprue diameter

二、流道: runner

热流道: hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道:round(full/half runner

流道电脑分析:mold flow analysis

流道平衡:runner balance

热嘴: hot sprue

热流道板:hot manifold

发热管:cartridge heater

探针: thermocouples

插头: connector plug

插座: connector socket

密封/封料: seal

三、运水:water line

喉塞:line lpug

喉管:tube

塑胶管:plastic tube

快速接头:jiffy quick connector plug/socker

四、模具零件: mold components

三板模:3-plate mold

二板模:2-plate mold

边钉/导边:leader pin/guide pin

边司/导套:bushing/guide bushing

中托司:shoulder guide bushing

中托边L:guide pin

顶针板:ejector retainner plate

托板: support plate

螺丝: screw

管钉:dowel pin

开模槽:ply bar scot

内模管位:core/cavity inter-lock

顶针: ejector pin

司筒:ejector sleeve

司筒针:ejector pin

推板:stripper plate

缩呵:movable core,return core core puller

扣机(尼龙拉勾):nylon latch lock

斜顶:lifter

模胚(架): mold base

上内模:cavity insert

下内模:core insert

行位(滑块): slide

镶件:insert

压座/斜鸡:wedge

耐磨板/油板:wedge wear plate

压条:plate

撑头: support pillar

唧嘴: sprue bushing

挡板:stop plate

定位圈:locating ring

锁扣:latch

扣鸡:parting lock set

推杆:push bar

栓打螺丝:S.H.S.B

顶板:eracuretun

活动臂:lever arm

分流锥:spure sperader

水口司:bush

垃圾钉:stop pin

隔片:buffle

弹弓柱:spring rod

弹弓:die spring

中托司:ejector guide bush

中托边:ejector guide pin

镶针:pin

销子:dowel pin

波子弹弓:ball catch

喉塞: pipe plug

锁模块:lock plate

斜顶:angle from pin

斜顶杆:angle ejector rod

尼龙拉勾:parting locks

活动臂:lever arm

复位键、提前回杆:early return bar

气阀:valves

斜导边:angle pin

术语:terms

承压平面平衡:parting surface support balance

模排气:parting line venting

回针碰料位:return pin and cavity interference

模总高超出啤机规格:mold base shut hight

顶针碰运水:water line interferes withejector pin

料位出上/下模:part from cavith (core)side

模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

不准用镶件: Do not use (core/cavity) insert

用铍铜做镶件: use beryllium copper insert

初步(正式)模图设计:preliinary (final) mold design

反呵:reverse core

弹弓压缩量:spring compressed length

稳定性好:good stability,stable

强度不够:insufficient rigidity

均匀冷却:even cooling

扣模:sticking

热膨胀:thero expansion

公差:tolorance

铜公(电极):copper electrode



Tags: 塑料 模具 英语 脱模剂